SKF軸承潤滑機械故障或早期磨損的主要原因有一半以上與潤滑技術管理有關.潤滑管理的主要任務是做好潤滑管理,防止和減少齒輪等摩擦運動部件的磨損或燒結,降低摩擦阻力,防止設備事故,提高設備生產效率,節約能源,提高能效和經濟效益.

More than half of the main causes of lubrication mechanical failure or early wear of SKF bearings are related to lubrication technology management. The main task of lubrication management is to do a good job of lubrication management, prevent and reduce wear or sintering of friction moving parts such as gears, reduce friction resistance, prevent equipment accidents, improve equipment production efficiency, save energy, and improve energy efficiency and economic benefits.

1.潤滑管理是一種專ye的技術管理.建立專職潤滑技術管理人員,制定潤滑管理制度,培訓潤滑技術知識.

1. Lubrication management is a special Ye technology management. Establish full-time lubrication technical management personnel, formulate lubrication management system, and train lubrication technical knowledge.

2.在油箱容量合理的前提下,通過保持油箱內的合理油位,經常向油箱內添加潤滑油,有利于油箱內的脫氣、除塵、除水和降低油溫,使油箱內的SKF軸承潤滑油始終處于合理的工作油位.

2. Under the premise of reasonable tank capacity, by maintaining the reasonable oil level in the tank and often adding lubricant to the tank, it is conducive to degassing, dust removal, water removal and oil temperature reduction in the tank, so that SKF bearing lubricant in the tank is always at a reasonable working oil level.

3.定期對油樣進行采樣,定期檢測氣味,、顏色、粘度,、含水量,、水分離性能、污染物的種類和含量,、泡沫的控制效果.當進入潤滑點的油的含水量超過個百分點時,機械磨損急劇增加;當含水量超過個百分點時,潤滑狀況將非常危險.做好測試記錄.

3. Regular sampling of oil samples, regular detection of odor, color, viscosity, water content, water separation performance, types and content of pollutants, control effect of foam. When the moisture content of the oil entering the lubrication point exceeds %, the mechanical wear increases sharply; when the moisture content exceeds %, the lubrication condition will be very dangerous. Make a good test record.

4.分析比較各種試驗記錄,預測潤滑bu良,制定改進或預防措施.系統的油位,、油質、油溫,、油壓控制bao警聯鎖應an全可靠,防止?jié)櫥鹿实陌l(fā)生.

4. Analysis and comparison of various test records, prediction of good lubrication bu, formulation of improvement or preventive measures. The oil level, oil quality, oil temperature and oil pressure of the system should be all reliable to prevent the occurrence of lubrication accidents.

目前鋼輪運行位置發生SKF軸承潤滑漏油時更換油封的具體步驟如下:

At present, the specific steps of replacing oil seal when SKF bearing lubrication leakage occurs in the running position of steel wheel are as follows:

1.松開振動電機的四個固定螺栓,拆下振動電機(不拆下電機上的橡膠軟管).

1. Loosen the four fixed bolts of the vibration motor and remove the vibration motor (without removing the rubber hose on the motor).

2.松開電機座上的七個螺栓并拆下電機座.

2. Loosen the seven bolts on the motor seat and remove the motor seat.

3.松開支撐板和支撐板上的八個固定螺栓,以及支撐板和前車架之間的連接螺栓.用減震器和支架降下支撐板.

3. Loosen the eight fixed bolts on the support plate and the support plate, and the connecting bolts between the support plate and the front frame. Lower the support plate with shock absorber and bracket.

4.松開擋板上的八個固定螺栓,拆下?lián)醢?

4. Loosen the eight fixed bolts on the baffle and remove the baffle.

5.搜索直徑小于內環的墊圈并將SKF軸承潤滑其放在外軸承座的軸頭上.

5. Search washers with diameters less than inner rings and lubricate SKF bearings on the axle head of the outer bearing seat.

6.拆下左蓋并放回緩沖板上.尋找七個用于擰緊左蓋和運行軸承座的M12*70螺栓.

6. Remove the left cover and put it back on the buffer plate. Look for seven M12*70 bolts for tightening the left cover and running the bearing seat.

7.通過按對角順序鎖緊七個螺栓,可將行走軸承座與其余螺栓一起拔出.活動軸承座調平后,可更換180 220 18的框架油封.

7. By locking seven bolts in diagonal order, the walking bearing seat can be pulled out together with other bolts. After leveling the movable bearing seat, the frame oil seal of 180 220 18 can be replaced.

應注意按與拆卸相反的順序安裝零件.骨架油封,、驅動軸承座和外軸承座應涂上更多的黃油,以避免壓力再次泄漏時損壞油封.

Attention should be paid to installing parts in reverse order of disassembly. The skeleton oil seal, drive bearing seat and outer bearing seat should be coated with more butter to avoid damage to the oil seal when pressure leaks again.

文章來自:SKF軸承潤滑 -

Article from: SKF Bearing Lubrication -

文章來自:INA軸承潤滑 -

Articles from: INA Bearing Lubrication -

文章來自:NSK軸承潤滑

Article from: NSK Bearing Lubrication

QQ:

電話:0

手機:/