定期檢查滾子徐州SKF軸承對于保持軸承的**佳狀態和反映發現的問題非常重要。軸承使用注意事項及相關知識,。

Regular inspection of roller Xuzhou SKF bearings is very important to keep the bearings in good condition and to reflect the problems found. Matters needing attention in the use of bearings and related knowLEDge.

首先,，我們應該強調保持滾子軸承潤滑和清潔的重要性,。因此，在檢查軸承之前,，首先清洗軸承表面,，然后去除軸承周圍的零件。油封是一個非常脆弱的部分,。在檢查和拆卸過程中,，應注意不要施加太大的力以免損壞零件。然后仔細檢查滾子軸承及其周圍部件的油封,。如果有任何不好的癥狀,，必*須更換,。油封不*良會導致軸承損壞，使?jié)L子徐州SKF軸承渾濁異常,，導致設備停機,。

First of all, we should emphasize the importance of keeping roller bearings lubricated and clean. Therefore, before inspecting the bearing, first clean the bearing su-ce, and then remove the parts around the bearing. Oil seal is a very fragile part. During inspection and disassembly, care should be taken not to exert too much force to avoid damage to parts. Then carefully inspect the oil seals of roller bearings and their surrounding parts. If there are any bad symptoms, they must be replaced. Poor oil seal will lead to bearing damage, make the SKF bearing turbidity abnormal roller Xuzhou, leading to equipment shutdown.

其次，我們還需要檢查滾子軸承的潤滑油,。潤滑不僅對軸承,，而且對所有進口軸承都非常重要。但是請注意,，給軸承加太多的潤滑脂是不明智的,。

Secondly, we also need to check the lubricating oil of roller bearings. Lubrication is very important not only for bearings, but also for all imported bearings. But please note that it is not wise to add too much grease to bearings.

滾子軸承潤滑劑的檢驗方法如下：

The inspection methods for roller bearing lubricants are as follows:

在手指間擦一點油。如果有污染物,，摸摸,。或在手背上涂一層薄薄的潤滑劑來檢查密封,。

Rub a little oil between your fingers. If there are contaminants, feel them. Or apply a thin layer of lubricant on the back of your hand to check the seal.

然后更換滾子徐州SKF軸承的潤滑油,。

Then change the lubricating oil of Xuzhou SKF bearing.

帶潤滑劑的滾子軸承應該充滿新鮮油，如果可能的話,，在排出舊油后以低速旋轉幾分鐘,。使油收集盡可能多的殘留污染物，然后去除油,。注：使用前應過濾機油。當用潤滑脂替換軸承中的潤滑脂時,，所用的分離器應避免棉和軸承的任何部分之間的任何接觸,。由于這些殘留的纖維可能楔入軋件之間并造成損傷，特別是在小軸承的應用中,，應更加注意這個問題,。

Roller bearings with lubricants should be filled with fresh oil and, if possible, rotate at a low speed for a few minutes after discharging the old oil. Make the oil collect as many residual pollutants as possible, and then remove the oil. Note: The oil should be filtered before use. When replacing grease in bearings with grease, the separator used should avoid any contact between cotton and any part of the bearing. As these residual fibers may wedge between the rolled parts and cause damage, especially in the application of small bearings, more attention should be paid to this problem.

經過一段時間的運動，振動和噪聲保持在一定的水平,，頻譜非常單一,，只有頻率的一到兩倍。三倍工頻以上的頻譜很少出現,。滾動徐州SKF軸承處于非常穩定的狀態,，已經進入了穩定的工作循環。

After a period of movement, the vibration and noise remain at a certain level, the spectrum is very single, only one or two times the frequency. Frequency spectrum above triple power frequency rarely appears. The rolling Xuzhou SKF bearing is in a very stable state and has entered a stable working cycle.

連續運行后,，軸承振動和噪聲開始增加,，有時出現異常聲音，但振動增加緩慢,。此時,，角接觸球軸承的峰值開始突然達到一定值,。我們認為，軸承的特征是它在這個時候的初始失效,。

After continuous operation, bearing vibration and noise begin to increase, sometimes abnormal sound occurs, but vibration increases slowly. At this time, the peak value of angular contact ball bearings begins to suddenly reach a certain value. We believe that the bearing is characterized by its initial failure at this time.

文章來自：徐州SKF軸承 www.wh-skf.com

Article from: Xuzhou SKF Bearing www.wh-skf.com

文章來自：徐州INA軸承 www.ina-china.cn

Article from: Xuzhou INA Bearing www.ina-China.cn

文章來自：徐州NSK軸承 www.klbbearings.com

Article from: Xuzhou NSK Bearing www.klbbearings.com

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757